Page 1 of 3

Tell Me The Best Way To Use Depth Charges

Posted: Wed Apr 07, 2004 1:47 am
by kmcdonne
Ok Enigma players... what are your tricks re depth charges? I heard that the voice commands. Per "Altreer"...

"I found a loop hole that allows me to get a pretty good estimate, when you know that a sub is below you and you are a little a head or on top of it, if you are able to use microphone commands, say engage target, this will show the distance you are from the sub, but if you are on top of it it will show you the depth of the submarine! Then you say set depth charges nnn and then say roll charges. Then you got them."

What other things have you discovered that work? Any advice? Sub missions are fun but I want to try surface missions. I have not been able to sink a sub yet.

Tell Me The Best Way To Use Depth Charges

Posted: Wed Apr 07, 2004 5:46 pm
by Sharaz
i dont wait until im on top of hte sub, i start issueing "engage target" as im closing in from 500 meters. i keep a calculator in hand. i get as best estimate "surface" distance from the BTAC, and use the distance reading from the reply from the officer. the square root of (distance reading)squared - (surface distance)squared is your depth.

set charges, and keep on steaming. i re-calculate every 30 seconds or so.

Tell Me The Best Way To Use Depth Charges

Posted: Thu Apr 08, 2004 12:15 am
by odog1999
Wait untill after your fantail passes where you want to drop, not your bow. It also helps to come in a angles and drop charges across the bow of the sub. It usually stops while you're closing in, then starts moving after you drop the charges... And rus right into them.

Tell Me The Best Way To Use Depth Charges

Posted: Thu Apr 08, 2004 1:38 am
by kmcdonne
On the square root stuff...

can you provide an example actually using some numbers/distances?

I'd really appreciate it.

Tell Me The Best Way To Use Depth Charges

Posted: Thu Apr 08, 2004 5:58 am
by odog1999
For a good example, let's say I'm approaching a sub that shows up at 200m on the closest zoom. At the same time, I give the "engage target" command. The response comes back as "Engaging target bearing 250 range 280." Then you'd put into your calculator √(280^2-200^2), which gives you a depth of ~196m. Repeat again at the 100m recticle to establish rate of dive/surfacing. Usually on the first or second time the Sub goes angel2:

Tell Me The Best Way To Use Depth Charges

Posted: Thu Apr 08, 2004 9:08 pm
by JackAubreyRN
Here's My Favorite Strategem for killing those pesky subs. It's a little risky when there are multiple subs around, but quite effective.

Notice that once a sub fires torpedoes at you and dives it usually proceeds to over 100m depth. Steam past the sub's location then use the pivot turn and run up right behind the sub. Drop charges at 150m when the sub's icon is behind your stern within the first ring of the tactical display, up to that line.

Works for me; no sub manages to survive my tactic.

Good Luck.

Tell Me The Best Way To Use Depth Charges

Posted: Wed Apr 21, 2004 11:14 pm
by odog1999
Ok. Someone emailed me about this, but I got a reply that "Mail quota exceeded" for that user. So if you want me to reply, send another message when your mailbox is cleaned out ;)

Tell Me The Best Way To Use Depth Charges

Posted: Sat Apr 24, 2004 2:09 am
by kyee7k
easy answer for you. just as your stern is just about to pass the target, fire full pattern for the depth charges. oh, and before i forget, set your depth charges for 170 on the depth gauge. i've yet to miss any of my subs (mmm...cookies).

Tell Me The Best Way To Use Depth Charges

Posted: Sat Apr 24, 2004 11:33 pm
by kyee7k
before i forget, just before you get into dropping distance, put your engine on idle and coast your way over them, and just before they cross your stern (set depth to 170), mash the fire button to enable the depth charge. no matter what depth they are, they will be gone. :D

Tell Me The Best Way To Use Depth Charges

Posted: Sun Jun 13, 2004 3:32 pm
by sgdavis
The response comes back as "Engaging target bearing 250 range 280."
Great advice, thanks! My microphone works and I can issue voice commands and get a response, but the response is in text. How can I get the crewmen to speak? I read that there was a separate download or something? I enabled the voice response and have the volume all the way up on that.

Thanks for any help!

--Steve